Spray Guns, Paint Spray Guns, Finishing  Equipment, Adhesives, Sealants, Air Line Equipment, Industrial Lubricants, Decorating Products
Manufacturers:
Airflow
Besta
Bimba Stainless
De-Sta-Co
DeVILBISS
Dynaclean
Elcometer
Fuchs Lubritech
LoctiteŽ
Threadlocking
Pipe & Thread Sealing
Gasketing
Retaining
Instant Bonding
Structural Bonding
Flexible Sealing & Bonding
Lubrication: Oils & Dry Film
Lubrication: Greases
Lubrication: Anti-Seize
Metal-filled Compounds
Wearing Compounds
Cleaning
Surface Preparation
Emergency Repair Products
Equipment
LoctiteŽ Medical Adhesives
London Fan Co.
Norgren
Numatics
PCL Air Technology
Robohand
Titan Airless Spray Technology
Wagner
Weka
HOMEABOUT USPRODUCTSCONTACT USLOCATIONLINKS
      
Gasketing -
Sealing of Flanges
Loctite
      
Features:
No shimming effect - controlled tolerances, no need for re-torquing
Fill all voids - reduce the need for a fine surface finish of flanges
Parts can be disassembled easily even after extended service
Resists high pressure when fully cured
      
Handy Hints:
If there are old traces of gasket left on the parts to be sealed, clean with LoctiteŽ 7200 gasket remover
All parts must be clean and dry before sealing - use LoctiteŽ 7063
Anaerobic products cure between metal surfaces in the absence of air
Use activator LoctiteŽ 7240 in cold conditions to speed up the cure
      
        Does the existing gasket need to be used as a shim?
        |
        Yes
        ||
        Coat existing gasketPositioning cut gaskets
        ||
        PasteSemi-solid
        ||
Solution:5203534
Gasket TypeFormed-in-placeUse with cut gaskets
Flange TypeRigidRigid or Flexible
Cure MethodAnaerobicAnaerobic
Tack-Free TimeN.A.N.A.
Temperature Resistance+150°C+150°C
Instant SealExcellentExcellent
Oil ResistanceExcellentGood
Water/Glycol ResistanceModerateGood
Pack Sizes50ml, 300ml cartridge9g, 19g stick
      
      
        Does the existing gasket need to be used as a shim?
        |
        No
        |
        What gap must the sealant fill?
        |
        Up to 0.25mmGreater than 0.25mm
        ||
        MetalsPlastic or combined plastic/metal parts
        ||||||
        Semi-solidGelPastePastePastePaste
        ||||||
Solution:  54857451851059105699
Gasket TypeFormed-in-placeFormed-in-placeFormed-in-placeFormed-in-placeFormed-in-
place
Formed-in-
place
Flange TypeRigidRigidRigidRigidFlexibleFlexible
Cure MethodAnaerobicAnaerobicAnaerobicAnaerobicMoistureMoisture
Tack-Free TimeN.A.N.A.N.A.N.A.20 min.10 min.
Temperature Resistance+150°C+150°C+150°Cup to +200°C+200°C+200°C
Instant SealExcellentExcellentExcellentExcellentExcellentExcellent
Oil ResistanceGoodExcellentExcellentExcellentExcellentGood
Water/Glycol ResistanceGoodExcellentExcellentExcellentModerateExcellent
Pack Sizes9g, 18g stick50ml, 160ml
cartridge
250ml tube
50ml,
65ml,
300ml
cartridge
50ml,
160ml,
250ml
cartridge
300ml
cartridge
300ml
cartridge
      
      
  If you would like to receive a copy of our LoctiteŽ Product Catalogue, click here
Murphy Engineers Limited, John F. Kennedy Ave, Naas Road, Dublin 12, Ireland
        
Tel: +353 1 4500088        Fax: +353 1 4500602        Email: sales@murphy-engineers.ie        Powered by: go2web